A Practical Guide to Drill Bits

Posted by cjs727 on Nov 1st, 2011 | 12 comments

When starting a project that requires drilling you should first make sure that you are using the right type of drill bit. If you use the wrong type you could damage the material you are working on. You can determine which drill bit to use based on what material you will be drilling into. Here is a practical and basic guide about drill bits and which are best suited for some of the more commonly used materials used in DIY projects.

Metal

When drilling into a non-ferrous metal, you will need to use High Speed Steel (HSS) drill bits that are made with partially ground tips. Non-ferrous metals include: aluminum, copper, zinc, brass and non-alloyed steel. If drilling into stainless steel, a different type of drill bit should be used. For this material, drill bits made of cobalt-alloyed High Speed Steel (HSS-E) or drill bits which have a titanium coating are best. They are more expensive than regular HSS drill bits but they allow for drilling without having to worry about excessive wear to the bits themselves.

Wood

When drilling into wood, brad point bits are best. Brad point drill bits have a long centering tip with two pre-cutting spurs. These spurs are used to score the wood fibers before the internal cutting edges cut them out cleanly.  Forstner drill bits, hardware drill bits or hinge cutting bits are usually used for larger diameters and there are auger bits for boring deep holes into wood.

Masonry

Drilling into brick or concrete will require the use of an impact drill or rotary hammer. If you are drilling any such material that contains perforated stones with a porous material, only rotary drilling should be preformed (without impact). This also applies when drilling into porous bricks and boarded walls. In order to drill into these materials, you will need a masonry drill bit. Masonry drill bits have tungsten-carbide tips designed to give the strength needed to penetrate the hard material and used with a rotary drill to lessen the likelihood of cracking and splitting that would happen with an impact drill.

If you are not sure which drill bit to use, don’t guess because this could have negative results. Ask someone who is knowledgeable, either by way of experience in the use of drills or those trained in the sale of such tools. Those who work at hardware stores usually have the knowledge needed and will be able to assist you with which bit is best for each type of job and material you will be working with.

12 Responses to “A Practical Guide to Drill Bits”

1. Rachel says:

   December 28, 2011 at 11:09 am

   Thank you for the great article- very helpful. My compliments on your website layout as well! Keep up the great work. I will definitely be posting this article on my Twitter page! #drillbits

   Reply
2. Anonymous says:

   December 27, 2011 at 7:05 pm

   I will be subscribing to this feed. Important points were made here. Thanks for sharing.

   Reply
3. Anonymous says:

   December 8, 2011 at 6:26 pm

   Thanks a bunch for sharing this with all folks. Bookmarked.

   Reply
4. Anonymous says:

   December 6, 2011 at 12:34 pm

   A person essentially assist to make significantly articles I would state. That is the very first time I frequented your web page and so far? I surprised with the research you made to create this actual submit extraordinary. Excellent process!

   Reply
5. Paul Sanchez says:

   December 6, 2011 at 10:06 am

   Hello, I simply wanted to take time to make a comment and say I have really enjoyed reading your site.

   Reply
6. Anonymous says:

   December 5, 2011 at 6:22 am

   Thanks for that awesome posting. It saved MUCH time

   Reply
7. B Berger says:

   December 4, 2011 at 8:44 am

   This blog is wonderful i like studying your posts. Keep up the good paintings! You realize, many persons are looking around for this information, you could help them greatly.

   Reply
8. Anonymous says:

   December 3, 2011 at 11:20 am

   Wonderful work! This is the kind of information that should be shared across the internet. Disgrace on Google for now not positioning this submit higher! Thanks =)

   Reply
9. Anonymous says:

   November 22, 2011 at 8:40 pm

   Just found you on aol. Fantastic write-up, I was just thinking about something comparable. Might start out writing a blog myself! I’m a fan! Kudos

   Reply
10. Anonymous says:

    November 17, 2011 at 7:44 pm

    Happy to be visiting your blog again, it has been weeks for me. Well, this is the article that I’ve been waited for so long. Thanks,

    Reply
11. Walter says:

    November 13, 2011 at 10:18 am

    Many thanks for trying to describe the terminology to the inexperienced persons!

    Reply
12. Arron says:

    November 11, 2011 at 7:51 pm

    Great! thanks for the share!

    Reply